2.2KW Water Cooled Spindle Kit CNC Milling Spindle Motor 2.2KW VFD Inverter 80mm Clamp Water Pump P
[33049006221] Package List: 2.2kw/220V Kit Package List: 1 x 2.2KW CNC Water Cooled Spindle Motor 1 x 2.2KW/220V VDF 1 x 3.5M Water Pump 1 x 5M Water Pipes 1 x 80mm Spindle Clamp 13 x ER20 Collet (1,2,3.175,4,5,6,7,8,9,10,11,12.7,13mm) 1.5kw/220V Kit Package List: 1 x 1.5KWCNCWater Cooled Spindle Motor 1 x 1.5KW/220V VDF 1 x 3.5M Water Pump 1 x 5M Water Pipes 1 x 65mm Spindle Clamp 13 x ER11Collet (1,2,3.175,4,5,6,7,8,9,10,11,12.7,13mm) Notice: 1. As the original factory value setting is for a normal 50Hz motor, so please change the inverter parameters according to your motor. 2. For this spindle kit , the working frequency of the spindle is 400Hz, so you need to change the inverter parameter according to 400Hz. 3. Please kindly note , the spindle must start at 400HZ, 24000 rpm , and then slowly adjust the speed to your own needs,but speed can not be lower than 12,000 rpm absolutely can not start at low speed, the spindle will immediately burn off !!! 4.Please make sure the wire is connecting right (both the inverter and the spindle) , if you don't know how to connect the wires ,please feel free to contact us at first. 5.Please set the correct parameters before connecting with motor.If you don't know how to process,please feel free to contact us at first. Warranty :1 year from the date you purchased!! Basic Date 1. CNC Spindle Motor Size:80mm Power:2.2KW Voltage:220V Frequency:0-400Hz Speed:0-24000rpm Water Cooling ER20 collet Runout off:less than 0.005mm Grease Lubrication 4pcs bearing C7005X2 C7002X2 Preparations before using 1.Spindle working environment temperature is usually -10 ~ 40 . 2.Before installing the first electric spindle axis head turned by hand, should feel flexible, non-blocking phenomenon. About spindle using: 1.Spindle in the preservation and transportation, high-speed grease inside the bearing state will change, customers should be running at low speed for 30 minutes. 3000 rpm and then follow the poor increase, run 20 minutes each. Spindle and the inverter should be working together. The inverter's specifications and parameter settings need match spindles parameter. 2.Connect the inverter spindle, three-phase inverter power cord should be soldered in the plug 1 (U), 2 (V), 3 (W) feet, 4 feet for the ground. After the power is turned on, to observe whether the spindle rotation axis indicates the direction consistent. If inconsistency should be immediately shut down, replace the inverter and spindle connected two wires of three-phase power supply. 3.It should ensure that before use of water-cooled spindle, the cooling system is working properly. Every day before using the spindle must be running at low speed for 15-20 minutes. Clamping the cutters to spindle, collet nuts ,collets,cutters must be clean enough. Shank inserted into the collet must be greater than 15mm. Care and maintenance 1.Water cooled spindle MUST be used with water pump. Otherwise the spindle will soon broken. 2.AC spindle motor MUST use with inverter. The power of inverter need equal or bigger than the spindle power. Before using,please set up the inverter parameters suitable for spindle. Otherwise the spindle and inverter will broken at once. 3.When you use the spindle,the noise is not same as always,please STOP the spindle at once. You may need to replace the spindle bearings. PID control; advanced calculus PID closed-loop arithmetic, quick responding speed and high suitability; 2.Inverter parameters: 1.5KW/220V VFD 2.2kw/ 220V VFD Input Voltage 220V 220V Output Voltage 220VAC 220VAC Output Frequency 50/60 Hz 50/60 Hz Input Frequency 0-400 Hz 0-400 Hz Input Phase 1 phase 1 phase Output Phase 3 phase 3 phase 3.water pump Special engraving machine spindle motor cooling water pump, 3.5m, 80w high power! Voltage: 220v (can be directly connected to the household power supply) Head: 3.5 m Flow: 3500L / h Power: 80w Usage: placed directly after the pumps and pipes connected to the tank, the tank water level height should be more than 2.5 times the height of the pump of the best! Avoid dry dry! 4. collet : 1set er20 13pcs (1,2,3.175,4,5,6,7,8,9,10,11,12.7,13mm) 5. clamp: 80mm clamp 6. 5M Water pipe: Size:5M 6mm (ID)*8mm (OD) If you want to purchase ITEMS from China, please give me your product list, let me give you a quote. Our company is focused on providing CNC /3D PRINTER parts and accessories. We have our own cnc processing plant, and cooperate with some other factories, this will help control costs and ensure quality. Friend, We really hope to be your < CHINA SOURCING AGENT >, make your China sourcing work more convenient and efficient!
US $248.68Grab Now 38% US $154.18
Tidak ada komentar:
Posting Komentar